#ifndef _EPICARDIUM_H
#define _EPICARDIUM_H
#include <stdint.h>
#include <errno.h>
#ifndef __SPHINX_DOC
/* stddef.h is not recognized by hawkmoth for some odd reason */
#include <stddef.h>
#else
typedef unsigned int size_t;
#endif /* __SPHINX_DOC */
/*
* These definitions are required for the code-generator. Please don't touch!
*/
#ifndef API
#define API(id, def) def
#endif
#ifndef API_ISR
#define API_ISR(id, isr) void isr(void);
#endif
/*
* IDs for all defined API calls. These IDs should not be needed in application
* code on any side.
*/
/* clang-format off */
#define API_UART_WRITE 0x1
#define API_UART_READ 0x2
#define API_LEDS_SET 0x3
#define API_VIBRA_SET 0x4
#define API_VIBRA_VIBRATE 0x5
#define API_STREAM_READ 0x6
#define API_INTERRUPT_ENABLE 0x7
#define API_INTERRUPT_DISABLE 0x8
#define API_LIGHT_SENSOR_RUN 0x9
#define API_LIGHT_SENSOR_GET 0xa
#define API_LIGHT_SENSOR_STOP 0xb
#define API_DISP_OPEN 0x10
#define API_DISP_CLOSE 0x11
#define API_DISP_PRINT 0x12
#define API_DISP_CLEAR 0x13
#define API_DISP_UPDATE 0x14
#define API_DISP_LINE 0x15
#define API_DISP_RECT 0x16
#define API_DISP_CIRC 0x17
#define API_DISP_PIXEL 0x18
#define API_FILE_OPEN 0x30
#define API_FILE_CLOSE 0x31
#define API_FILE_READ 0x32
#define API_FILE_WRITE 0x34
#define API_FILE_FLUSH 0x35
#define API_FILE_SEEK 0x36
#define API_FILE_TELL 0x37
#define API_FILE_STAT 0x38
/* clang-format on */
typedef uint32_t api_int_id_t;
/**
* Interrupts
* ==========
* Next to API calls, Epicardium API also has an interrupt mechanism to serve
* the other direction. These interrupts can be enabled/disabled
* (masked/unmasked) using :c:func:`epic_interrupt_enable` and
* :c:func:`epic_interrupt_disable`.
*/
/**
* Enable/unmask an API interrupt.
*
* :param int_id: The interrupt to be enabled
*/
API(API_INTERRUPT_ENABLE, int epic_interrupt_enable(api_int_id_t int_id));
/**
* Disable/mask an API interrupt.
*
* :param int_id: The interrupt to be disabled
*/
API(API_INTERRUPT_DISABLE, int epic_interrupt_disable(api_int_id_t int_id));
/**
* The following interrupts are defined:
*/
/* clang-format off */
/** Reset Handler? **TODO** */
#define EPIC_INT_RESET 0
/** ``^C`` interrupt. See :c:func:`epic_isr_ctrl_c` for details. */
#define EPIC_INT_CTRL_C 1
/* Debug interrupt, please ignore */
#define EPIC_INT_BHI160_TEST 2
API_ISR(EPIC_INT_BHI160_TEST, epic_isr_bhi160_test);
/* Number of defined interrupts. */
#define EPIC_INT_NUM 3
/* clang-format on */
API_ISR(EPIC_INT_RESET, epic_isr_reset);
/**
* UART/Serial Interface
* =====================
*/
/**
* Write a string to all connected serial devices. This includes:
*
* - Real UART, whose pins are mapped onto USB-C pins. Accessible via the HW-debugger.
* - A CDC-ACM device available via USB.
* - Maybe, in the future, bluetooth serial?
*
* :param str: String to write. Does not necessarily have to be NULL-terminated.
* :param length: Amount of bytes to print.
*/
API(API_UART_WRITE, void epic_uart_write_str(const char *str, intptr_t length));
/**
* Blocking read a single character from any connected serial device.
* ``epic_uart_read_chr`` only returns once one byte has been read.
*
* .. todo::
*
* This API function is currently in violation of the API rules.
*
* :return: The byte.
*/
API(API_UART_READ, char epic_uart_read_chr(void));
/**
* **Interrupt Service Routine**
*
* A user-defineable ISR which is triggered when a ``^C`` (``0x04``) is received
* on any serial input device. This function is weakly aliased to
* :c:func:`epic_isr_default` by default.
*
* To enable this interrupt, you need to enable :c:data:`EPIC_INT_CTRL_C`:
*
* .. code-block:: cpp
*
* epic_interrupt_enable(EPIC_INT_CTRL_C);
*/
API_ISR(EPIC_INT_CTRL_C, epic_isr_ctrl_c);
/**
* LEDs
* ====
*/
/**
* Set one of card10's RGB LEDs to a certain color.
*
* :param led: Which led to set. 0-10 are the leds on the top and 11-14 are the 4 "ambient" leds.
* :param r: Red component of the color.
* :param g: Green component of the color.
* :param b: Blue component of the color.
*/
API(API_LEDS_SET, void epic_leds_set(int led, uint8_t r, uint8_t g, uint8_t b));
/**
* Sensor Data Streams
* ===================
* A few of card10's sensors can do continuous measurements. To allow
* performant access to their data, the following function is made for generic
* access to streams.
*/
/**
* Read sensor data into a buffer. ``epic_stream_read()`` will read as many
* sensor samples into the provided buffer as possible and return the number of
* samples written. If no samples are available, ``epic_stream_read()`` will
* return ``0`` immediately.
*
* ``epic_stream_read()`` expects the provided buffer to have a size which is a
* multiple of the sample size for the given stream. For the sample-format and
* size, please consult the sensors documentation.
*
* Before reading the internal sensor sample queue, ``epic_stream_read()`` will
* call a sensor specific *poll* function to allow the sensor driver to fetch
* new samples from its hardware. This should, however, never take a long
* amount of time.
*
* :param int sd: Sensor Descriptor. You get sensor descriptors as return
* values when activating the respective sensors.
* :param void* buf: Buffer where sensor data should be read into.
* :param size_t count: How many bytes to read at max. Note that fewer bytes
* might be read. In most cases, this should be ``sizeof(buf)``.
* :return: Number of data packets read (**not** number of bytes) or a negative
* error value. Possible errors:
*
* - ``-ENODEV``: Sensor is not currently available.
* - ``-EBADF``: The given sensor descriptor is unknown.
* - ``-EINVAL``: ``count`` is not a multiple of the sensor's sample size.
* - ``-EBUSY``: The descriptor table lock could not be acquired.
*
* **Example**:
*
* .. code-block:: cpp
*
* #include "epicardium.h"
*
* struct foo_measurement sensor_data[16];
* int foo_sd, n;
*
* foo_sd = epic_foo_sensor_enable(9001);
*
* while (1) {
* n = epic_stream_read(
* foo_sd,
* &sensor_data,
* sizeof(sensor_data)
* );
*
* // Print out the measured sensor samples
* for (int i = 0; i < n; i++) {
* printf("Measured: %?\n", sensor_data[i]);
* }
* }
*/
API(API_STREAM_READ, int epic_stream_read(int sd, void *buf, size_t count));
/**
* Misc
* ====
*/
/**
* Turn vibration motor on or off
*
* :param status: 1 to turn on, 0 to turn off.
*/
API(API_VIBRA_SET, void epic_vibra_set(int status));
/**
* Turn vibration motor on for a given time
*
* :param millis: number of milliseconds to run the vibration motor.
*/
API(API_VIBRA_VIBRATE, void epic_vibra_vibrate(int millis));
/**
* Display
* =======
*/
/** Line-Style */
enum disp_linestyle {
/** */
LINESTYLE_FULL = 0,
/** */
LINESTYLE_DOTTED = 1
};
/** Fill-Style */
enum disp_fillstyle {
/** */
FILLSTYLE_EMPTY = 0,
/** */
FILLSTYLE_FILLED = 1
};
/**
* Locks the display.
*
* :return: ``0`` on success or a negative value in case of an error:
*
* - ``-EBUSY``: Display was already locked from another task.
*/
API(API_DISP_OPEN, int epic_disp_open());
/**
* Unlocks the display again.
*
* :return: ``0`` on success or a negative value in case of an error:
*
* - ``-EBUSY``: Display was already locked from another task.
*/
API(API_DISP_CLOSE, int epic_disp_close());
/**
* Causes the changes that have been written to the framebuffer
* to be shown on the display
*/
API(API_DISP_UPDATE, int epic_disp_update());
/**
* Prints a string into the display framebuffer
*
* :param posx: x position to print to. 0 <= x <= 160
* :param posy: y position to print to. 0 <= y <= 80
* :param pString: string to print
* :param fg: foreground color in rgb565
* :param bg: background color in rgb565
* :return: ``0`` on success or a negative value in case of an error:
*
* - ``-EBUSY``: Display was already locked from another task.
*/
API(API_DISP_PRINT,
int epic_disp_print(
uint16_t posx,
uint16_t posy,
const char *pString,
uint16_t fg,
uint16_t bg)
);
/**
* Fills the whole screen with one color
*
* :param color: fill color in rgb565
* :return: ``0`` on success or a negative value in case of an error:
*
* - ``-EBUSY``: Display was already locked from another task.
*/
API(API_DISP_CLEAR, int epic_disp_clear(uint16_t color));
/**
* Draws a pixel on the display
*
* :param x: x position; 0 <= x <= 160
* :param y: y position; 0 <= y <= 80
* :param color: pixel color in rgb565
* :return: ``0`` on success or a negative value in case of an error:
*
* - ``-EBUSY``: Display was already locked from another task.
*/
API(API_DISP_PIXEL,
int epic_disp_pixel(
uint16_t x,
uint16_t y,
uint16_t color)
);
/**
* Draws a line on the display
*
* :param xstart: x starting position; 0 <= x <= 160
* :param ystart: y starting position; 0 <= y <= 80
* :param xend: x ending position; 0 <= x <= 160
* :param yend: y ending position; 0 <= y <= 80
* :param color: line color in rgb565
* :param linestyle: 0 for solid, 1 for dottet (almost no visual difference)
* :param pixelsize: thickness of the line; 1 <= pixelsize <= 8
* :return: ``0`` on success or a negative value in case of an error:
*
* - ``-EBUSY``: Display was already locked from another task.
*/
API(API_DISP_LINE,
int epic_disp_line(
uint16_t xstart,
uint16_t ystart,
uint16_t xend,
uint16_t yend,
uint16_t color,
enum disp_linestyle linestyle,
uint16_t pixelsize)
);
/**
* Draws a rectangle on the display
*
* :param xstart: x coordinate of top left corner; 0 <= x <= 160
* :param ystart: y coordinate of top left corner; 0 <= y <= 80
* :param xend: x coordinate of bottom right corner; 0 <= x <= 160
* :param yend: y coordinate of bottom right corner; 0 <= y <= 80
* :param color: line color in rgb565
* :param fillstyle: 0 for empty, 1 for filled
* :param pixelsize: thickness of the rectangle outline; 1 <= pixelsize <= 8
* :return: ``0`` on success or a negative value in case of an error:
*
* - ``-EBUSY``: Display was already locked from another task.
*/
API(API_DISP_RECT,
int epic_disp_rect(
uint16_t xstart,
uint16_t ystart,
uint16_t xend,
uint16_t yend,
uint16_t color,
enum disp_fillstyle fillstyle,
uint16_t pixelsize)
);
/**
* Draws a circle on the display
*
* :param x: x coordinate of the center; 0 <= x <= 160
* :param y: y coordinate of the center; 0 <= y <= 80
* :param rad: radius of the circle
* :param color: fill and outline color of the circle (rgb565)
* :param fillstyle: 0 for empty, 1 for filled
* :param pixelsize: thickness of the circle outline; 1 <= pixelsize <= 8
* :return: ``0`` on success or a negative value in case of an error:
*
* - ``-EBUSY``: Display was already locked from another task.
*/
API(API_DISP_CIRC,
int epic_disp_circ(
uint16_t x,
uint16_t y,
uint16_t rad,
uint16_t color,
enum disp_fillstyle fillstyle,
uint16_t pixelsize)
);
/**
* Start continuous readout of the light sensor. Will read light level
* at preconfigured interval and make it available via `epic_light_sensor_get()`.
*
* If the continuous readout was already running, this function will silently pass.
*
*
* :return: `0` if the start was successful or a negative error value
* if an error occured. Possible errors:
*
* - ``-EBUSY``: The timer could not be scheduled.
*/
API(API_LIGHT_SENSOR_RUN, int epic_light_sensor_run());
/**
* Get the last light level measured by the continuous readout.
*
* :param uint16_t* value: where the last light level should be written.
* :return: `0` if the readout was successful or a negative error
* value. Possible errors:
*
* - ``-ENODATA``: Continuous readout not currently running.
*/
API(API_LIGHT_SENSOR_GET, int epic_light_sensor_get(uint16_t* value));
/**
* Stop continuous readout of the light sensor.
*
* If the continuous readout wasn't running, this function will silently pass.
*
* :return: `0` if the stop was sucessful or a negative error value
* if an error occured. Possible errors:
*
* - ``-EBUSY``: The timer stop could not be scheduled.
*/
API(API_LIGHT_SENSOR_STOP, int epic_light_sensor_stop());
/**
* File
* ====
* Except for :c:func:`epic_file_open`, which models C stdio's ``fopen``
* function, ``close``, ``read`` and ``write`` model `close(2)`_, `read(2)`_ and
* `write(2)`_. All file-related functions return >= ``0`` on success and
* ``-Exyz`` on failure, with error codes from errno.h (``EIO``, ``EINVAL``
* etc.)
*
* .. _close(2): http://man7.org/linux/man-pages/man2/close.2.html
* .. _read(2): http://man7.org/linux/man-pages/man2/read.2.html
* .. _write(2): http://man7.org/linux/man-pages/man2/write.2.html
*/
/** */
API(
API_FILE_OPEN,
int epic_file_open(const char* filename, const char* modeString)
);
/** */
API(API_FILE_CLOSE, int epic_file_close(int fd));
/** */
API(API_FILE_READ, int epic_file_read(int fd, void* buf, size_t nbytes));
/** */
API(
API_FILE_WRITE,
int epic_file_write(int fd, const void* buf, size_t nbytes)
);
/** */
API(API_FILE_FLUSH, int epic_file_flush(int fd));
/** */
API(API_FILE_SEEK, int epic_file_seek(int fd, long offset, int whence));
/** */
API(API_FILE_TELL, int epic_file_tell(int fd));
/** */
enum epic_stat_type {
/** */
EPICSTAT_FILE,
/** */
EPICSTAT_DIR,
};
/** */
typedef struct epic_stat_t {
/** */
enum epic_stat_type type;
} epic_stat_t;
/**
* stat path
*
* This does not follow posix convention, but rather takes
* a path as parameter. This aligns more with libff's API and
* also this has been implemented for python import support, which
* passes the filename as well.
*
* :param const char* filename: path to stat
* :param epic_stat_t* stat: pointer to result
*
* :return: `0` on success, negative on error
*/
API(API_FILE_STAT, int epic_file_stat(const char* path, epic_stat_t* stat));
#endif /* _EPICARDIUM_H */