diff --git a/Hello_World/Makefile b/Hello_World/Makefile
index 7fee86e9bb4b85f4cc9236a169e3430c8d92d2b5..02d4d978a06834b67511ee9796996756000d424c 100644
--- a/Hello_World/Makefile
+++ b/Hello_World/Makefile
@@ -67,11 +67,13 @@ CMSIS_ROOT=$(LIBS_DIR)/CMSIS
# Source files for this test (add path to VPATH below)
SRCS = main.c
-SRCS += ../lib/card10/oled96.c
-SRCS += ../lib/card10/fonts.c
-SRCS += ../lib/card10/pmic.c
+SRCS += oled96.c
+SRCS += fonts.c
+SRCS += pmic.c
+SRCS += bosch.c
SRCS += bhy_support.c bhy_uc_driver.c bhy.c
SRCS += MAX77650-Arduino-Library.c
+SRCS += bme680.h
# Where to find source files for this test
VPATH = .
@@ -88,6 +90,9 @@ VPATH += ../lib/bosch/BHy1_driver_and_MCU_solution/driver/src
IPATH += ../lib/maxim/MAX77650-Arduino-Library
VPATH += ../lib/maxim/MAX77650-Arduino-Library
+IPATH += ../lib/bosch/BME680_driver
+VPATH += ../lib/bosch/BME680_driver
+
# Enable assertion checking for development
PROJ_CFLAGS+=-DMXC_ASSERT_ENABLE
diff --git a/Hello_World/main.c b/Hello_World/main.c
index 1d0268ef493ea552389ffc023e0037f08f378837..4fd813ca8542b0fa5105e03c1de13d1fbdf26381 100644
--- a/Hello_World/main.c
+++ b/Hello_World/main.c
@@ -57,6 +57,8 @@
#include "Bosch_PCB_7183_di03_BMI160_BMM150-7183_di03.2.1.11696_170103.h"
#include "bhy_uc_driver.h"
#include "pmic.h"
+#include "bme680.h"
+#include "bosch.h"
/***** Definitions *****/
@@ -104,7 +106,6 @@ int main(void)
int count = 0;
printf("Hello World!\n");
- TMR_Delay(MXC_TMR0, MSEC(1000), 0);
//Setup the I2CM
I2C_Shutdown(MXC_I2C0_BUS0);
@@ -113,6 +114,12 @@ int main(void)
I2C_Shutdown(MXC_I2C1_BUS0);
I2C_Init(MXC_I2C1_BUS0, I2C_FAST_MODE, NULL);
+ pmic_init();
+ pmic_set_led(0, 0);
+ pmic_set_led(1, 0);
+ pmic_set_led(2, 0);
+ TMR_Delay(MXC_TMR0, MSEC(1000), 0);
+
#if 0
NVIC_EnableIRQ(I2C0_IRQn); // Not sure if we actually need this when not doing async requests
#endif
@@ -143,6 +150,21 @@ int main(void)
}
+ struct bme680_dev gas_sensor;
+ gas_sensor.dev_id = BME680_I2C_ADDR_PRIMARY;
+ gas_sensor.intf = BME680_I2C_INTF;
+ gas_sensor.read = card10_bosch_i2c_read;
+ gas_sensor.write = card10_bosch_i2c_write;
+ gas_sensor.delay_ms = card10_bosch_delay;
+ gas_sensor.amb_temp = 25;
+
+ int8_t rslt = BME680_OK;
+ rslt = bme680_init(&gas_sensor);
+ if(rslt != BME680_OK) {
+ printf("Failed to init BME680\n");
+ }
+
+
// Enable 32 kHz output
RTC_SquareWave(MXC_RTC, SQUARE_WAVE_ENABLED, F_32KHZ, NOISE_IMMUNE_MODE, NULL);
@@ -164,7 +186,6 @@ int main(void)
printf("%02x: 0x%06x\n", i, val);
}
- pmic_init();
while (1) {
pmic_set_led(0, 31);
diff --git a/bmetest/Makefile b/bmetest/Makefile
index c89e5e9aa5cc3766c10fd05a3dbe6334de4b81c0..02d4d978a06834b67511ee9796996756000d424c 100644
--- a/bmetest/Makefile
+++ b/bmetest/Makefile
@@ -67,9 +67,10 @@ CMSIS_ROOT=$(LIBS_DIR)/CMSIS
# Source files for this test (add path to VPATH below)
SRCS = main.c
-SRCS += ../lib/card10/oled96.c
-SRCS += ../lib/card10/fonts.c
-SRCS += ../lib/card10/pmic.c
+SRCS += oled96.c
+SRCS += fonts.c
+SRCS += pmic.c
+SRCS += bosch.c
SRCS += bhy_support.c bhy_uc_driver.c bhy.c
SRCS += MAX77650-Arduino-Library.c
SRCS += bme680.h
diff --git a/bmetest/main.c b/bmetest/main.c
index e85909b9f258ee6c0b21a28f7b08eda86abf7cf3..b7edeb288fdf234e8422ef6dafb879321c615f87 100644
--- a/bmetest/main.c
+++ b/bmetest/main.c
@@ -49,55 +49,17 @@
#include "board.h"
#include "tmr_utils.h"
#include "i2c.h"
-#include "rtc.h"
-#include "spi.h"
#include "gpio.h"
#include "oled96.h"
-#include "bhy.h"
-#include "Bosch_PCB_7183_di03_BMI160_BMM150-7183_di03.2.1.11696_170103.h"
-#include "bhy_uc_driver.h"
#include "pmic.h"
#include "bme680.h"
+#include "bosch.h"
/***** Definitions *****/
-
-void user_delay_ms(uint32_t period)
-{
- TMR_Delay(MXC_TMR0, MSEC(period), 0);
-}
-
-void hexdump(uint8_t *data, uint8_t len);
-int8_t user_i2c_read(uint8_t dev_id, uint8_t reg_addr, uint8_t *reg_data, uint16_t len)
-{
- //printf("sensor_i2c_read 0x%02x %d\n", reg_addr, len);
- if(I2C_MasterWrite(MXC_I2C1_BUS0, dev_id << 1, ®_addr, 1, 1) == 1) {
- //printf("setup read ok\n");
- int l = I2C_MasterRead(MXC_I2C1_BUS0, dev_id << 1, reg_data, len, 0);
- //printf("read:"); hexdump(reg_data, l);
- return l == len ? 0 : -1;
- }
- return -1;
-}
-
-int8_t user_i2c_write(uint8_t dev_id, uint8_t reg_addr, uint8_t *reg_data, uint16_t len)
-{
- //printf("sensor_i2c_write 0x%02x:", reg_addr); hexdump(reg_data, len);
- uint8_t buf[len + 1];
- buf[0] = reg_addr;
- memcpy(buf + 1, reg_data, len);
- int l = I2C_MasterWrite(MXC_I2C1_BUS0, dev_id << 1, buf, len + 1, 0);
- //printf("wrote: %d\n", l);
- return l == len + 1 ? 0 : -1;
-}
-
// *****************************************************************************
int main(void)
{
- int count = 0;
-
printf("Hello World!\n");
- TMR_Delay(MXC_TMR0, MSEC(1000), 0);
-
//Setup the I2CM
I2C_Shutdown(MXC_I2C0_BUS0);
I2C_Init(MXC_I2C0_BUS0, I2C_FAST_MODE, NULL);
@@ -105,6 +67,12 @@ int main(void)
I2C_Shutdown(MXC_I2C1_BUS0);
I2C_Init(MXC_I2C1_BUS0, I2C_FAST_MODE, NULL);
+ pmic_init();
+ pmic_set_led(0, 0);
+ pmic_set_led(1, 0);
+ pmic_set_led(2, 0);
+ TMR_Delay(MXC_TMR0, MSEC(1000), 0);
+
#if 0
NVIC_EnableIRQ(I2C0_IRQn); // Not sure if we actually need this when not doing async requests
#endif
@@ -124,13 +92,6 @@ int main(void)
}
}
- pmic_init();
- pmic_set_led(0, 0);
- pmic_set_led(1, 0);
- pmic_set_led(2, 0);
-
- TMR_Delay(MXC_TMR0, MSEC(1000), 0);
-
oledInit(0x3c, 0, 0);
oledFill(0x00);
oledWriteString(0, 0, "Hello", 0);
@@ -140,9 +101,9 @@ int main(void)
struct bme680_dev gas_sensor;
gas_sensor.dev_id = BME680_I2C_ADDR_PRIMARY;
gas_sensor.intf = BME680_I2C_INTF;
- gas_sensor.read = user_i2c_read;
- gas_sensor.write = user_i2c_write;
- gas_sensor.delay_ms = user_delay_ms;
+ gas_sensor.read = card10_bosch_i2c_read;
+ gas_sensor.write = card10_bosch_i2c_write;
+ gas_sensor.delay_ms = card10_bosch_delay;
/* amb_temp can be set to 25 prior to configuring the gas sensor
* or by performing a few temperature readings without operating the gas sensor.
*/
diff --git a/imutest/Makefile b/imutest/Makefile
index 7fee86e9bb4b85f4cc9236a169e3430c8d92d2b5..7103aa7df95cb593000287b8c6f0a2efe8d8b5e2 100644
--- a/imutest/Makefile
+++ b/imutest/Makefile
@@ -67,9 +67,10 @@ CMSIS_ROOT=$(LIBS_DIR)/CMSIS
# Source files for this test (add path to VPATH below)
SRCS = main.c
-SRCS += ../lib/card10/oled96.c
-SRCS += ../lib/card10/fonts.c
-SRCS += ../lib/card10/pmic.c
+SRCS += oled96.c
+SRCS += fonts.c
+SRCS += pmic.c
+SRCS += bosch.c
SRCS += bhy_support.c bhy_uc_driver.c bhy.c
SRCS += MAX77650-Arduino-Library.c
# Where to find source files for this test
diff --git a/imutest/main.c b/imutest/main.c
index a1730a37c8bd496485f57fc03b8e241ad933fcb9..adabba9ba6c226dc600c317f749b964a807f6115 100644
--- a/imutest/main.c
+++ b/imutest/main.c
@@ -89,27 +89,6 @@ void I2C0_IRQHandler(void)
}
#endif
-uint32_t ecg_read_reg(uint8_t reg)
-{
- spi_req_t req;
- uint8_t tx_data[] = {(reg << 1) | 1, 0, 0, 0};
- uint8_t rx_data[] = {0, 0, 0, 0};
- req.tx_data = tx_data;
- req.rx_data = rx_data;
- req.len = 4;
- req.bits = 8;
- req.width = SPI17Y_WIDTH_1;
- req.ssel = 0;
- req.deass = 1;
- req.ssel_pol = SPI17Y_POL_LOW;
- req.tx_num = 0;
- req.rx_num = 0;
-
- SPI_MasterTrans(SPI, &req);
-
- return (rx_data[1] << 16) | (rx_data[2] << 8) | rx_data[3];
-}
-
static void sensors_callback_vector(bhy_data_generic_t * sensor_data, bhy_virtual_sensor_t sensor_id)
{
printf("x=%d, y=%d, z=%d status=%d\n",
@@ -189,7 +168,6 @@ static void sensors_callback_rotation_vector(bhy_data_generic_t * sensor_data, b
int main(void)
{
printf("Hello World!\n");
- TMR_Delay(MXC_TMR0, MSEC(1000), 0);
//Setup the I2CM
I2C_Shutdown(MXC_I2C0_BUS0);
@@ -198,6 +176,13 @@ int main(void)
I2C_Shutdown(MXC_I2C1_BUS0);
I2C_Init(MXC_I2C1_BUS0, I2C_FAST_MODE, NULL);
+ pmic_init();
+ pmic_set_led(0, 0);
+ pmic_set_led(1, 0);
+ pmic_set_led(2, 0);
+
+ TMR_Delay(MXC_TMR0, MSEC(1000), 0);
+
#if 0
NVIC_EnableIRQ(I2C0_IRQn); // Not sure if we actually need this when not doing async requests
#endif
@@ -217,13 +202,6 @@ int main(void)
}
}
- pmic_init();
- pmic_set_led(0, 0);
- pmic_set_led(1, 0);
- pmic_set_led(2, 0);
-
- TMR_Delay(MXC_TMR0, MSEC(1000), 0);
-
#if 0
oledInit(0x3c, 0, 0);
oledFill(0x00);
diff --git a/lib/bosch/BHy1_driver_and_MCU_solution/driver/src/bhy_support.c b/lib/bosch/BHy1_driver_and_MCU_solution/driver/src/bhy_support.c
index 2c83fe6d3f3b604153b01943461b77f22154e00d..85866227351cce3f92784711a1c83cee9df187cc 100644
--- a/lib/bosch/BHy1_driver_and_MCU_solution/driver/src/bhy_support.c
+++ b/lib/bosch/BHy1_driver_and_MCU_solution/driver/src/bhy_support.c
@@ -55,9 +55,8 @@
/********************************************************************************/
#include "bhy_support.h"
#include "bhy_uc_driver_config.h"
+#include "bosch.h"
-#include "i2c.h"
-#include "tmr_utils.h"
#include <stdio.h>
#include <string.h>
@@ -67,30 +66,17 @@
static struct bhy_t bhy;
static char *version = BHY_MCU_REFERENCE_VERSION;
-#define I2C_DEVICE MXC_I2C1_BUS0
/********************************************************************************/
/* EXTERN FUNCTION DECLARATIONS */
/********************************************************************************/
static int8_t sensor_i2c_write(uint8_t addr, uint8_t reg, uint8_t *p_buf, uint16_t size)
{
- uint8_t buf[size + 1];
-
- //printf("sensor_i2c_write 0x%02x %d\n", reg, size);
- buf[0] = reg;
- memcpy(buf + 1, p_buf, size);
-
- int l = I2C_MasterWrite(I2C_DEVICE, addr << 1, buf, size + 1, 0);
- return l == size + 1 ? BHY_SUCCESS : BHY_ERROR;
+ return card10_bosch_i2c_write(addr, reg, p_buf, size) == 0 ? BHY_SUCCESS : BHY_ERROR;
}
static int8_t sensor_i2c_read(uint8_t addr, uint8_t reg, uint8_t *p_buf, uint16_t size)
{
- //printf("sensor_i2c_read 0x%02x %d\n", reg, size);
- if(I2C_MasterWrite(I2C_DEVICE, addr << 1, ®, 1, 1) == 1) {
- int l = I2C_MasterRead(I2C_DEVICE, addr << 1, p_buf, size, 0);
- return l == size ? BHY_SUCCESS : BHY_ERROR;
- }
- return BHY_ERROR;
+ return card10_bosch_i2c_read(addr, reg, p_buf, size) == 0 ? BHY_SUCCESS : BHY_ERROR;
}
/********************************************************************************/
@@ -135,7 +121,7 @@ int8_t bhy_initialize_support(void)
*/
void bhy_delay_msec(uint32_t msec)
{
- TMR_Delay(MXC_TMR0, MSEC(msec), 0);
+ card10_bosch_delay(msec);
}
/*!
* @brief provides a print function to the bhy driver on DD2.0 platform
diff --git a/lib/card10/bosch.c b/lib/card10/bosch.c
new file mode 100644
index 0000000000000000000000000000000000000000..772208dd796c7bda01da008978a98948b4254fd1
--- /dev/null
+++ b/lib/card10/bosch.c
@@ -0,0 +1,55 @@
+#include "i2c.h"
+#include "tmr_utils.h"
+
+#include <stdint.h>
+#include <stdio.h>
+#include <string.h>
+
+#define I2C_DEVICE MXC_I2C1_BUS0
+/********************************************************************************/
+/* EXTERN FUNCTION DECLARATIONS */
+/********************************************************************************/
+
+#if 0
+static void hexdump(uint8_t *data, uint8_t len)
+{
+ for(int i=0; i<len; i++) {
+ printf("%02x ", data[i]);
+ }
+ printf("\n");
+}
+#endif
+
+int8_t card10_bosch_i2c_write(uint8_t addr, uint8_t reg, uint8_t *p_buf, uint16_t size)
+{
+ uint8_t buf[size + 1];
+
+ //printf("sensor_i2c_write 0x%02x:", reg); hexdump(p_buf, size);
+ buf[0] = reg;
+ memcpy(buf + 1, p_buf, size);
+
+ int l = I2C_MasterWrite(I2C_DEVICE, addr << 1, buf, size + 1, 0);
+ //printf("wrote: %d\n", l);
+ return l == size + 1 ? 0 : -1;
+ //return l == size + 1 ? BHY_SUCCESS : BHY_ERROR;
+}
+
+int8_t card10_bosch_i2c_read(uint8_t addr, uint8_t reg, uint8_t *p_buf, uint16_t size)
+{
+ //printf("sensor_i2c_read 0x%02x %d\n", reg, size);
+ if(I2C_MasterWrite(I2C_DEVICE, addr << 1, ®, 1, 1) == 1) {
+ //printf("setup read ok\n");
+ int l = I2C_MasterRead(I2C_DEVICE, addr << 1, p_buf, size, 0);
+ //printf("read:"); hexdump(p_buf, l);
+ return l == size ? 0 : -1;
+ //return l == size ? BHY_SUCCESS : BHY_ERROR;
+
+ }
+ return -1;
+ //return BHY_ERROR;
+}
+
+void card10_bosch_delay(uint32_t msec)
+{
+ TMR_Delay(MXC_TMR0, MSEC(msec), 0);
+}
diff --git a/lib/card10/bosch.h b/lib/card10/bosch.h
new file mode 100644
index 0000000000000000000000000000000000000000..b183a85dbd9f1a247d3858948fe1ccb47dd40132
--- /dev/null
+++ b/lib/card10/bosch.h
@@ -0,0 +1,10 @@
+#ifndef BOSCH_H
+#define BOSCH_H
+
+#include <stdint.h>
+
+int8_t card10_bosch_i2c_write(uint8_t addr, uint8_t reg, uint8_t *p_buf, uint16_t size);
+int8_t card10_bosch_i2c_read(uint8_t addr, uint8_t reg, uint8_t *p_buf, uint16_t size);
+void card10_bosch_delay(uint32_t msec);
+
+#endif