Forked from
card10 / firmware
1890 commits behind the upstream repository.
main.c 5.66 KiB
/*******************************************************************************
* Copyright (C) 2016 Maxim Integrated Products, Inc., All Rights Reserved.
*
* Permission is hereby granted, free of charge, to any person obtaining a
* copy of this software and associated documentation files (the "Software"),
* to deal in the Software without restriction, including without limitation
* the rights to use, copy, modify, merge, publish, distribute, sublicense,
* and/or sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included
* in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS
* OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
* IN NO EVENT SHALL MAXIM INTEGRATED BE LIABLE FOR ANY CLAIM, DAMAGES
* OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
* ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*
* Except as contained in this notice, the name of Maxim Integrated
* Products, Inc. shall not be used except as stated in the Maxim Integrated
* Products, Inc. Branding Policy.
*
* The mere transfer of this software does not imply any licenses
* of trade secrets, proprietary technology, copyrights, patents,
* trademarks, maskwork rights, or any other form of intellectual
* property whatsoever. Maxim Integrated Products, Inc. retains all
* ownership rights.
*
* $Date: 2018-09-04 22:13:32 +0000 (Tue, 04 Sep 2018) $
* $Revision: 37649 $
*
******************************************************************************/
/**
* @file main.c
* @brief Hello World!
* @details This example uses the UART to print to a terminal and flashes an LED.
*/
/***** Includes *****/
#include <stdio.h>
#include <stdint.h>
#include <string.h>
#include "mxc_config.h"
#include "led.h"
#include "board.h"
#include "tmr_utils.h"
#include "i2c.h"
#include "rtc.h"
#include "spi.h"
#include "gpio.h"
#include "oled96.h"
#include "bhy.h"
#include "Bosch_PCB_7183_di03_BMI160_BMM150-7183_di03.2.1.11696_170103.h"
#include "bhy_uc_driver.h"
#include "pmic.h"
/***** Definitions *****/
#define I2C_DEVICE MXC_I2C0_BUS0
#define SPI SPI0
#define SPI_SPEED 1000000 // Bit Rate
/***** Globals *****/
static const gpio_cfg_t motor_pin = {PORT_0, PIN_8, GPIO_FUNC_OUT, GPIO_PAD_NONE};
/***** Functions *****/
#if 0
void I2C0_IRQHandler(void)
{
I2C_Handler(I2C_DEVICE);
return;
}
#endif
uint32_t ecg_read_reg(uint8_t reg)
{
spi_req_t req;
uint8_t tx_data[] = {(reg << 1) | 1, 0, 0, 0};
uint8_t rx_data[] = {0, 0, 0, 0};
req.tx_data = tx_data;
req.rx_data = rx_data;
req.len = 4;
req.bits = 8;
req.width = SPI17Y_WIDTH_1;
req.ssel = 0;
req.deass = 1;
req.ssel_pol = SPI17Y_POL_LOW;
req.tx_num = 0;
req.rx_num = 0;
SPI_MasterTrans(SPI, &req);
return (rx_data[1] << 16) | (rx_data[2] << 8) | rx_data[3];
}
// *****************************************************************************
int main(void)
{
int count = 0;
printf("Hello World!\n");
TMR_Delay(MXC_TMR0, MSEC(1000), 0);
//Setup the I2CM
I2C_Shutdown(MXC_I2C0_BUS0);
I2C_Init(MXC_I2C0_BUS0, I2C_FAST_MODE, NULL);
I2C_Shutdown(MXC_I2C1_BUS0);
I2C_Init(MXC_I2C1_BUS0, I2C_FAST_MODE, NULL);
#if 0
NVIC_EnableIRQ(I2C0_IRQn); // Not sure if we actually need this when not doing async requests
#endif
uint8_t dummy[1] = {0};
// "7-bit addresses 0b0000xxx and 0b1111xxx are reserved"
for (int addr = 0x8; addr < 0x78; ++addr) {
// A 0 byte write does not seem to work so always send a single byte.
int res = I2C_MasterWrite(MXC_I2C0_BUS0, addr << 1, dummy, 1, 0);
if(res == 1) {
printf("Found (7 bit) address 0x%02x on I2C0\n", addr);
}
res = I2C_MasterWrite(MXC_I2C1_BUS0, addr << 1, dummy, 1, 0);
if(res == 1) {
printf("Found (7 bit) address 0x%02x on I2C1\n", addr);
}
}
oledInit(0x3c, 0, 0);
oledFill(0x00);
oledWriteString(0, 0, "Hello", 0);
oledWriteString(0, 2, "my name is", 0);
oledWriteString(0, 4, "card10", 1);
if(bhy_driver_init(bhy1_fw)) {
printf("Failed to init bhy\n");
}
// Enable 32 kHz output
RTC_SquareWave(MXC_RTC, SQUARE_WAVE_ENABLED, F_32KHZ, NOISE_IMMUNE_MODE, NULL);
// Enable SPI
sys_cfg_spi_t spi17y_master_cfg;
spi17y_master_cfg.map = MAP_A;
spi17y_master_cfg.ss0 = Enable;
spi17y_master_cfg.ss1 = Disable;
spi17y_master_cfg.ss2 = Disable;
if (SPI_Init(SPI, 0, SPI_SPEED, spi17y_master_cfg) != 0) {
printf("Error configuring SPI\n");
while (1);
}
for(int i=0; i<0x20; i++) {
uint32_t val = ecg_read_reg(i);
printf("%02x: 0x%06x\n", i, val);
}
pmic_init();
while (1) {
pmic_set_led(0, 31);
pmic_set_led(1, 0);
pmic_set_led(2, 0);
TMR_Delay(MXC_TMR0, MSEC(200), 0);
pmic_set_led(0, 0);
pmic_set_led(1, 31);
pmic_set_led(2, 0);
TMR_Delay(MXC_TMR0, MSEC(200), 0);
pmic_set_led(0, 0);
pmic_set_led(1, 0);
pmic_set_led(2, 31);
TMR_Delay(MXC_TMR0, MSEC(200), 0);
pmic_set_led(0, 0);
pmic_set_led(1, 0);
pmic_set_led(2, 0);
GPIO_OutSet(&motor_pin);
TMR_Delay(MXC_TMR0, MSEC(500), 0);
GPIO_OutClr(&motor_pin);
TMR_Delay(MXC_TMR0, MSEC(1000), 0);
printf("count = %d\n", count++);
}
}