- added svn props for newly added files

git-svn-id: svn://svn.berlios.de/openocd/trunk@610 b42882b7-edfa-0310-969c-e2dbd0fdcd60

src/target/interface/amontec-tiny.cfg

-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 0
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
+#interface
+interface ft2232
+ft2232_device_desc "Amontec JTAGkey A"
+ft2232_layout jtagkey
+ft2232_vid_pid 0x0403 0xcff8
+jtag_speed 0
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200

src/target/interface/calao-usb-a9260-c01.cfg

-#
-# Calao Systems USB-A9260-C01
-#
-# http://www.calao-systems.com/
-#
-interface ft2232
-ft2232_layout jtagkey
-ft2232_device_desc "USB-A9260"
-ft2232_vid_pid 0x0403 0x6010
-script interface/calao-usb-a9260.cfg
-script target/at91sam9260minimal.cfg
+#
+# Calao Systems USB-A9260-C01
+#
+# http://www.calao-systems.com/
+#
+interface ft2232
+ft2232_layout jtagkey
+ft2232_device_desc "USB-A9260"
+ft2232_vid_pid 0x0403 0x6010
+script interface/calao-usb-a9260.cfg
+script target/at91sam9260minimal.cfg

src/target/interface/calao-usb-a9260-c02.cfg

-#
-# Calao Systems USB-A9260-C02
-#
-# http://www.calao-systems.com/
-#
-interface ft2232
-ft2232_layout jtagkey
-ft2232_device_desc "USB-A9260 A"
-ft2232_vid_pid 0x0403 0x6001
-script interface/calao-usb-a9260.cfg
-script target/at91sam9260minimal.cfg
+#
+# Calao Systems USB-A9260-C02
+#
+# http://www.calao-systems.com/
+#
+interface ft2232
+ft2232_layout jtagkey
+ft2232_device_desc "USB-A9260 A"
+ft2232_vid_pid 0x0403 0x6001
+script interface/calao-usb-a9260.cfg
+script target/at91sam9260minimal.cfg

src/target/interface/calao-usb-a9260.cfg

-#
-# Calao Systems USB-A9260 common -C01 -C02 setup
-#
-# http://www.calao-systems.com/
-#
-# See calao-usb-a9260-c01.cfg and calao-usb-a9260-c02.cfg
-#
-# note: you must have an openocd version where jtag_speed sets two values
-#       trunk ver 606 contains the fix for this particular issue which can
-#      be seen if jtag_speed does not set two separate values
-#
-jtag_speed 1200 0
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
-
+#
+# Calao Systems USB-A9260 common -C01 -C02 setup
+#
+# http://www.calao-systems.com/
+#
+# See calao-usb-a9260-c01.cfg and calao-usb-a9260-c02.cfg
+#
+# note: you must have an openocd version where jtag_speed sets two values
+#       trunk ver 606 contains the fix for this particular issue which can
+#      be seen if jtag_speed does not set two separate values
+#
+jtag_speed 1200 0
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200
+

src/target/interface/str9-comstick.cfg

-interface ft2232
-ft2232_device_desc "STR9-comStick A"
-ft2232_layout comstick
+interface ft2232
+ft2232_device_desc "STR9-comStick A"
+ft2232_layout comstick

src/target/target/at91sam9260minimal.cfg

-######################################
-# Target:    Atmel AT91SAM9260
-######################################
-
-reset_config trst_and_srst
-
-#jtag_device <IR length> <IR capture> <IR mask> <IDCODE instruction>
-jtag_device 4 0x1 0xf 0xe
-
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
-
-######################
-# Target configuration
-######################
-
-#target <type> <endianess> <reset mode> <JTAG pos> <variant>
-target arm926ejs little reset_run 0 arm926ejs
-run_and_halt_time 0 30
-
+######################################
+# Target:    Atmel AT91SAM9260
+######################################
+
+reset_config trst_and_srst
+
+#jtag_device <IR length> <IR capture> <IR mask> <IDCODE instruction>
+jtag_device 4 0x1 0xf 0xe
+
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200
+
+######################
+# Target configuration
+######################
+
+#target <type> <endianess> <reset mode> <JTAG pos> <variant>
+target arm926ejs little reset_run 0 arm926ejs
+run_and_halt_time 0 30
+

src/target/target/epc9301.cfg

-# Cirrus Logic EP9301 processor on an Olimex CS-E9301 board.
-jtag_device 4 0x1 0xf 0xe
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-#target configuration
-daemon_startup attach
-#target <type> <endianess> <reset mode>
-target arm920t little reset_halt 0
-working_area 0 0x80014000 0x1000 backup
-#flash configuration
-#flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options ...]
-flash bank cfi 0x60000000 0x1000000 2 2 0
+# Cirrus Logic EP9301 processor on an Olimex CS-E9301 board.
+jtag_device 4 0x1 0xf 0xe
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+#target configuration
+daemon_startup attach
+#target <type> <endianess> <reset mode>
+target arm920t little reset_halt 0
+working_area 0 0x80014000 0x1000 backup
+#flash configuration
+#flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options ...]
+flash bank cfi 0x60000000 0x1000000 2 2 0

src/target/target/ipx42x.cfg

-#xscale ixp42x CPU
-
-#use combined on interfaces or targets that cant set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 7 0x1 0x7f 0x7e
-#target configuration
-daemon_startup reset
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target xscale big run_and_halt 0 IXP42x
-run_and_halt_time 0 30
+#xscale ixp42x CPU
+
+#use combined on interfaces or targets that cant set TRST/SRST separately
+reset_config srst_only srst_pulls_trst
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 7 0x1 0x7f 0x7e
+#target configuration
+daemon_startup reset
+#target <type> <startup mode>
+#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
+target xscale big run_and_halt 0 IXP42x
+run_and_halt_time 0 30

src/target/target/lpc2129.cfg

-#LPC-2129 CPU
-#use combined on interfaces or targets that cant set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-#target configuration
-daemon_startup reset
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
-run_and_halt_time 0 30
-working_area 0 0x40000000 0x4000 nobackup
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum
+#LPC-2129 CPU
+#use combined on interfaces or targets that cant set TRST/SRST separately
+reset_config trst_and_srst srst_pulls_trst
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 4 0x1 0xf 0xe
+#target configuration
+daemon_startup reset
+#target <type> <startup mode>
+#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
+target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
+run_and_halt_time 0 30
+working_area 0 0x40000000 0x4000 nobackup
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum

src/target/target/netx500.cfg

-#Hilscher netX 500 CPU
-#use combined on interfaces or targets that cant set TRST/SRST separately
-reset_config trst_and_srst
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-#target configuration
-daemon_startup reset
-#target <type> <endianness> <startup mode> <chainpos> <variant>
-target arm926ejs little run_and_halt 0 arm926ejs
-run_and_halt_time 0 500
+#Hilscher netX 500 CPU
+#use combined on interfaces or targets that cant set TRST/SRST separately
+reset_config trst_and_srst
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 4 0x1 0xf 0xe
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+#target configuration
+daemon_startup reset
+#target <type> <endianness> <startup mode> <chainpos> <variant>
+target arm926ejs little run_and_halt 0 arm926ejs
+run_and_halt_time 0 500

src/target/target/omap5912.cfg

-#TI OMAP5912 dual core processor - http://www.ti.com 
-#on a OMAP5912 OSK board http://www.spectrumdigital.com.
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 38 0x0 0x0 0x0
-jtag_device 4  0x1 0x0 0xe
-jtag_device 8  0x0 0x0 0x0
-
-#target configuration
-daemon_startup reset
-
-#target <type> <endianness> <reset mode> <chainpos> <variant>
-target arm926ejs little run_and_init 1 arm926ejs
-target_script 0 reset event/omap5912_reset.script
-run_and_halt_time 0 30
-
-# omap5912 lcd frame buffer as working area
-working_area 0 0x20000000 0x3e800 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank cfi 0x00000000 0x1000000 2 2 0
+#TI OMAP5912 dual core processor - http://www.ti.com 
+#on a OMAP5912 OSK board http://www.spectrumdigital.com.
+
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config trst_and_srst
+
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 38 0x0 0x0 0x0
+jtag_device 4  0x1 0x0 0xe
+jtag_device 8  0x0 0x0 0x0
+
+#target configuration
+daemon_startup reset
+
+#target <type> <endianness> <reset mode> <chainpos> <variant>
+target arm926ejs little run_and_init 1 arm926ejs
+target_script 0 reset event/omap5912_reset.script
+run_and_halt_time 0 30
+
+# omap5912 lcd frame buffer as working area
+working_area 0 0x20000000 0x3e800 nobackup
+
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank cfi 0x00000000 0x1000000 2 2 0

src/target/target/pxa270.cfg

-#Marvell/Intel PXA270 Script
-# set jtag_nsrst_delay to the delay introduced by your reset circuit
-# the rest of the needed delays are built into the openocd program
-jtag_nsrst_delay 260
-# set the jtag_ntrst_delay to the delay introduced by a reset circuit
-# the rest of the needed delays are built into the openocd program
-jtag_ntrst_delay 0
-#use combined on interfaces or targets that can’t set TRST/SRST separately
-reset_config trst_and_srst separate
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 7 0x1 0x7f 0x7e
-#target configuration
-daemon_startup reset
-target xscale little reset_halt 0 pxa27x
-# maps to PXA internal RAM. If you are using a PXA255
-# you must initialize SDRAM or leave this option off
-working_area 0 0x5c000000 0x10000 nobackup
-run_and_halt_time 0 30
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-# works for P30 flash
-flash bank cfi 0x00000000 0x1000000 2 4 0
+#Marvell/Intel PXA270 Script
+# set jtag_nsrst_delay to the delay introduced by your reset circuit
+# the rest of the needed delays are built into the openocd program
+jtag_nsrst_delay 260
+# set the jtag_ntrst_delay to the delay introduced by a reset circuit
+# the rest of the needed delays are built into the openocd program
+jtag_ntrst_delay 0
+#use combined on interfaces or targets that can’t set TRST/SRST separately
+reset_config trst_and_srst separate
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 7 0x1 0x7f 0x7e
+#target configuration
+daemon_startup reset
+target xscale little reset_halt 0 pxa27x
+# maps to PXA internal RAM. If you are using a PXA255
+# you must initialize SDRAM or leave this option off
+working_area 0 0x5c000000 0x10000 nobackup
+run_and_halt_time 0 30
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+# works for P30 flash
+flash bank cfi 0x00000000 0x1000000 2 4 0

src/target/target/stm32stick.cfg

-# Hitex stm32 performance stick
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
-jtag_device 4 0x1 0xf 0xe
-
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target cortex_m3 little reset_halt 0
-run_and_halt_time 0 30
-
-working_area 0 0x20000000 16384 nobackup
-
-#flash bank str7x <base> <size> 0 0 <target#> <variant>
-flash bank stm32x 0 0 0 0 0
-
-# For more information about the configuration files, take a look at:
-# http://openfacts.berlios.de/index-en.phtml?title=Open+On-Chip+Debugger
+# Hitex stm32 performance stick
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config trst_and_srst
+
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 4 0x1 0xf 0xe
+jtag_device 5 0x1 0x1 0x1e
+jtag_device 4 0x1 0xf 0xe
+
+#target <type> <startup mode>
+#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
+target cortex_m3 little reset_halt 0
+run_and_halt_time 0 30
+
+working_area 0 0x20000000 16384 nobackup
+
+#flash bank str7x <base> <size> 0 0 <target#> <variant>
+flash bank stm32x 0 0 0 0 0
+
+# For more information about the configuration files, take a look at:
+# http://openfacts.berlios.de/index-en.phtml?title=Open+On-Chip+Debugger

src/target/target/str730.cfg

-#STR730 CPU
-
-#use combined on interfaces or targets that cant set TRST/SRST separately
-#reset_config trst_and_srst srst_pulls_trst
-reset_config trst_and_srst srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#jtag nTRST and nSRST delay
-jtag_nsrst_delay 500
-jtag_ntrst_delay 500
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-
-run_and_halt_time 0 30
-
-working_area 0 0x40000000 0x4000 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str7x 0x20000000 0x00040000 0 0 0 STR3x
-
+#STR730 CPU
+
+#use combined on interfaces or targets that cant set TRST/SRST separately
+#reset_config trst_and_srst srst_pulls_trst
+reset_config trst_and_srst srst_pulls_trst
+
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 4 0x1 0xf 0xe
+
+#jtag nTRST and nSRST delay
+jtag_nsrst_delay 500
+jtag_ntrst_delay 500
+
+#target configuration
+daemon_startup reset
+
+#target <type> <startup mode>
+#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
+target arm7tdmi little run_and_halt 0 arm7tdmi
+
+run_and_halt_time 0 30
+
+working_area 0 0x40000000 0x4000 nobackup
+
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank str7x 0x20000000 0x00040000 0 0 0 STR3x
+

src/target/target/str750.cfg

-#STR750 CPU
-
-#use combined on interfaces or targets that cant set TRST/SRST separately
-#reset_config trst_and_srst srst_pulls_trst
-reset_config trst_and_srst srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#jtag nTRST and nSRST delay
-jtag_nsrst_delay 500
-jtag_ntrst_delay 500
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-
-run_and_halt_time 0 30
-
-working_area 0 0x40000000 0x4000 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str7x 0x20000000 0x00040000 0 0 0 STR75x
-flash bank str7x 0x200C0000 0x00004000 0 0 0 STR75x
-
+#STR750 CPU
+
+#use combined on interfaces or targets that cant set TRST/SRST separately
+#reset_config trst_and_srst srst_pulls_trst
+reset_config trst_and_srst srst_pulls_trst
+
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 4 0x1 0xf 0xe
+
+#jtag nTRST and nSRST delay
+jtag_nsrst_delay 500
+jtag_ntrst_delay 500
+
+#target configuration
+daemon_startup reset
+
+#target <type> <startup mode>
+#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
+target arm7tdmi little run_and_halt 0 arm7tdmi
+
+run_and_halt_time 0 30
+
+working_area 0 0x40000000 0x4000 nobackup
+
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank str7x 0x20000000 0x00040000 0 0 0 STR75x
+flash bank str7x 0x200C0000 0x00004000 0 0 0 STR75x
+

src/target/target/str9comstick.cfg

-#Hitex STR9 Comstick
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-#use combined on interfaces or targets that cant set TRST/SRST separately
-reset_config trst_and_srst
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 8 0x1 0x1 0xfe
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
-#target configuration
-daemon_startup reset
-#target <type> <startup mode>
-#target arm966e <endianness> <reset mode> <chainpos> <variant>
-target arm966e little reset_halt 1 arm966e
-run_and_halt_time 0 30
-working_area 0 0x50000000 16384 nobackup
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str9x 0x00000000 0x00080000 0 0 0
+#Hitex STR9 Comstick
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+#use combined on interfaces or targets that cant set TRST/SRST separately
+reset_config trst_and_srst
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 8 0x1 0x1 0xfe
+jtag_device 4 0x1 0xf 0xe
+jtag_device 5 0x1 0x1 0x1e
+#target configuration
+daemon_startup reset
+#target <type> <startup mode>
+#target arm966e <endianness> <reset mode> <chainpos> <variant>
+target arm966e little reset_halt 1 arm966e
+run_and_halt_time 0 30
+working_area 0 0x50000000 16384 nobackup
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank str9x 0x00000000 0x00080000 0 0 0