- str91x protect_check fixed
- bank number now correctly given to str91x flash_config command


git-svn-id: svn://svn.berlios.de/openocd/trunk@211 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- str7 flash driver now checks correct busy bits depending on device
- str9 flash driver now disables ITCM order as per st programming manual
- added str7 disable_jtag command
- added gdb_detach command
- updated arm966e cp15 support
- fix crash on mingw build when enabling target_request debugmsgs

git-svn-id: svn://svn.berlios.de/openocd/trunk@209 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- flash autoerase <on|off> cmd added, default is off - flash banks are calculated and erased prior to write (flash write_image only)
- corrected array overrun in armv7m.c
- corrected breakpoint memory allocation bug
- image read now uses fgets, vastly improves reading of large files
- improved hex file reading, support for Linear Address Record added

git-svn-id: svn://svn.berlios.de/openocd/trunk@208 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- Clean up, remove unused variables and code in armv7, cortex_m3 and stellaris code 
- Move restore_context from cortex_m3 to armv7m
- Updated halt handling for cortex_m3


git-svn-id: svn://svn.berlios.de/openocd/trunk@206 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@201 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@200 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- use 'etm trigger_percent' setting when programming ETB trigger count
- fixed some small bugs in ETM trace analysis
- fixed minor bug in flash writing (thanks to Pavel Chromy)


git-svn-id: svn://svn.berlios.de/openocd/trunk@197 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@196 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- reworked presto.c to allow use of either FTD2XX or libftdi (libftdi not functional yet). Configure option changed from --enable-presto to 
--enable-presto_ftd2xx and --enable-presto_libftdi
- completed trace point support for use with ARM7/9 DCC
- completed debug message output with support for HEX dumps (1, 2 or 4 byte quantities)
- fixed bug in delete_debug_msg_receiver (thanks to Pavel Chromy)
- fixed bug in image_add_section (thanks to Pavel Chromy)
- at91sam7 sector erase reworked (thanks to Pavel Chromy)
- merge consecutive sections during flash image write to work around possible section alignment issues with LPC2000 targets



git-svn-id: svn://svn.berlios.de/openocd/trunk@194 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- make ep93xx and at91rm9200 bitbang JTAG interfaces dependant on ARM host (thanks to Vincent Palatin)
- various whitespace fixes
- removed various warnings
- add support for Debian GNU/kFreeBSD (thanks to Uwe Hermann)
- fix OpenOCD compilation for various platforms (thanks to Uwe Hermann and Vincent Palatin)
- switched order of JTAG chain examination and validation (examine first, then multiple validation tries even if examination failed)
- added target_request subsystem to handle requests from the target (debug messages and tracepoints implemented, future enhancements might include
semihosting, all ARM7/9 only for now)
- added support for GDB vFlashXXX packets (thanks to Pavel Chromy)
- added support for receiving data via ARM7/9 DCC
- reworked flash writing. the 'flash write' command is now deprecated and replaced by 'flash write_binary' (old syntax and behaviour) and 'flash
write_image' (write image files (bin, hex, elf, s19) to a target).
- added support for AMD/ST/SST 29F400B non-cfi flashes



git-svn-id: svn://svn.berlios.de/openocd/trunk@190 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added prepare_reset_halt handler for cortex_m3

git-svn-id: svn://svn.berlios.de/openocd/trunk@184 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fix multiple reads from FT2232 into same buffer location (thanks to Magnus Lundin)
- retry JTAG chain validation (thanks to Magnus Lundin)
- reworked GDB packet input handling (thanks to Pavel Chromy)
- output error message when setting a watchpoint failed
- removed duplicate out-of-bounds check in at91sam7.c (thanks to Pavel Chromy)


git-svn-id: svn://svn.berlios.de/openocd/trunk@181 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added support for Asix Presto JTAG interface (thanks to Pavel Chromy and Asix for making this addition possible)
- added support for usbprog (thanks to Benedikt Sauter)
- make OpenOCD listen for WM_QUIT messages on windows (thanks to Pavel Chromy)
- register at_exit handler to do necessary unregistering (thanks to Pavel Chromy)
- added dummy ETM capture driver to allow ETM to be registered without a capture driver


git-svn-id: svn://svn.berlios.de/openocd/trunk@180 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added declarations for 32bit fileio access functions (network byte order)
- fixed bug in etm trace dump file handling
- added XScale trace buffer decoding
- fixed arm_simulator ERROR numbers (-7xx used twice)
- fixed minor bug in debug output in stellaris.c


git-svn-id: svn://svn.berlios.de/openocd/trunk@178 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- ST STM32x flash support added
- cleaned up armv7m and cortex-m3 support, removed luminary specific code
- cortex-m3 16bit read/write added (required for STM32x flash programming)

git-svn-id: svn://svn.berlios.de/openocd/trunk@177 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@175 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added str9x programming using flash controller tap (str9xpec), including option bytes and device lock/unlock
- inttypes.h now used for long long printf style declarations

git-svn-id: svn://svn.berlios.de/openocd/trunk@174 b42882b7-edfa-0310-969c-e2dbd0fdcd60

Added support for NVGM bit 2 for AT91SAM7XC128/256 

git-svn-id: svn://svn.berlios.de/openocd/trunk@172 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@171 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@170 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed bug in ARM926EJ-S cache handling that caused cache linefills to be disabled after first debug entry
- added support for auto image type detection (thanks to Vincent Palatin)
- further work on ETM trace decoding (tested with a ETB interface using an ETM in normal 16-bit port mode, still experimental)



git-svn-id: svn://svn.berlios.de/openocd/trunk@169 b42882b7-edfa-0310-969c-e2dbd0fdcd60

This checkin is still experimental, not recommended for general use



git-svn-id: svn://svn.berlios.de/openocd/trunk@159 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- reworked etm/etb into a generic etm part with trace capture drivers (currently only etb supported)
- added XScale debug handler binary to repository
- added Thumb disassembling (thanks to Vincent Palatin for this patch)
- added support for non-CFI compatible flashes to cfi driver (currently only SST39VFxxx devices supported)
This checkin is experimental, not suitable for general use


git-svn-id: svn://svn.berlios.de/openocd/trunk@155 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed arm926ej-s CP15 register access handling
- correctly identify SYSCLK source in LPC3180 NAND flash controller driver


git-svn-id: svn://svn.berlios.de/openocd/trunk@139 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- output all of EmbeddedICE version register in error message
- update OpenOCD's idea of the current core mode, and immediately change core mode, on CPSR changes
- added support for CFI cmdset 0002 (patch by Andrew Dyer, thanks a lot)
- enhanced CFI cmdset 0002 support to Atmel AT49 flashes (thanks to Joerg Krein for providing test hardware)


git-svn-id: svn://svn.berlios.de/openocd/trunk@138 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed some compiler warnigns in amt_jtagaccel.c, bitbang.c, parport.c
- free working area and register stuff if str7x block write algorithm failed
- check PC after exiting a target algorithm in armv4_5.c


git-svn-id: svn://svn.berlios.de/openocd/trunk@135 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed compiler warnings throughout the code (thanks to Vincent Palatin for this patch)
- added support for accessing ETB (embedded trace buffer) registers


git-svn-id: svn://svn.berlios.de/openocd/trunk@134 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- reworked file i/o. every fileaccess (target, flash, nand, in future configuration, too) should now go through the fileio subsystem
- added support for reading IHEX files (through fileio)
- load/dump_binary renamed to the more generic load/dump_image <file> <address> ['bin'|'ihex']
- added NAND framework (preliminary)
- added support for the LPC3180 SLC and MLC NAND controllers (preliminary)
- fix initialization for parport
- gw16012 fixes/cleanups
- added EmbeddedICE version 7 (preliminary, reported on two LPC23xx devices so far)
- added 'arm7_9 etm <target#>' configuration command to enable access to the ETM registers


git-svn-id: svn://svn.berlios.de/openocd/trunk@132 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- add missing parentheses around macro parameters (thanks to Matthias Bauch for noticing this bug and providing a fix)


git-svn-id: svn://svn.berlios.de/openocd/trunk@130 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- complain about identify_chain scan with all bits one (jtag communication problem)
- add 0x80000 as a valid size for lpc2000_v2 flash banks (previously only the user accessible 0x7d000 were valid)


git-svn-id: svn://svn.berlios.de/openocd/trunk@129 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fix infinite recursion in target_init_handler (thanks to jw and Magnus Lundin)
- fix CFI flash handlign with buswidth < 32bit (thanks to Daniele Orio for reporting this)
- add support for reading JTAG device id (currently only as debug output on startup)
- cleaned up handling of EmbeddedICE registers. Supported functionality and register size now determined by EmbeddedICE version number.
- small cleanups/fixes


git-svn-id: svn://svn.berlios.de/openocd/trunk@124 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed bug in jtag.c where JTAG command type was wrong for PATHMOVE commands
- added lattice ISP cable (experimental)
- properly initialize parallel port (clear tristate bit)
- fixed jtag/Makefile.am that failed with some versions of autotools
- print error number if read() in gdbserver.c failed on Windows
- fixed handling of opcodes with bits 27-25 b011 (comment was correct, code had a bug)
- added support for AT91SAM7SE internal flash


git-svn-id: svn://svn.berlios.de/openocd/trunk@122 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added support for loading .bit files into Xilinx Virtex-II devices
- added support for the Gateworks GW16012 JTAG dongle
- merged CFI fixes from XScale branch
- a few minor fixes


git-svn-id: svn://svn.berlios.de/openocd/trunk@116 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- several small fixes
- retry reading from a FT2232 device on incomplete reads


git-svn-id: svn://svn.berlios.de/openocd/trunk@110 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added support for using Luminary Micro development board 'evb_lm3s811' as a JTAG interface (thanks to Magnus Lundin)


git-svn-id: svn://svn.berlios.de/openocd/trunk@106 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added support for AT91SAM7A devices (thanks to Magnus Lundin)
- updated README with pointer to Amontec's JTAGkeyTiny


git-svn-id: svn://svn.berlios.de/openocd/trunk@102 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- str75x flash support (Thanks to Spencer Oliver)
- correct reporting of T-Bit in CPSR (Thanks to John Hartman for reporting this)
- core-state (ARM/Thumb) can be switched by modifying CPSR
- fixed bug in gdb_server register handling
- register values > 32-bit should now be supported
- several minor fixes and enhancements



git-svn-id: svn://svn.berlios.de/openocd/trunk@100 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- cleaned up str7x flash erase and protect code (use two accesses to erase sectors in both banks)


git-svn-id: svn://svn.berlios.de/openocd/trunk@98 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@96 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- integrated patch from Magnus Lundin that fixes at91sam7 flash timing bugs and possible endianness problems (big endian hosts)
- correctly write trailing bytes on str7x flashes
- speed up str7x flash writing by offloading the algorithm to the target


git-svn-id: svn://svn.berlios.de/openocd/trunk@95 b42882b7-edfa-0310-969c-e2dbd0fdcd60