- fixed bug in jtag.c where JTAG command type was wrong for PATHMOVE commands
- added lattice ISP cable (experimental)
- properly initialize parallel port (clear tristate bit)
- fixed jtag/Makefile.am that failed with some versions of autotools
- print error number if read() in gdbserver.c failed on Windows
- fixed handling of opcodes with bits 27-25 b011 (comment was correct, code had a bug)
- added support for AT91SAM7SE internal flash


git-svn-id: svn://svn.berlios.de/openocd/trunk@122 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@117 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added support for loading .bit files into Xilinx Virtex-II devices
- added support for the Gateworks GW16012 JTAG dongle
- merged CFI fixes from XScale branch
- a few minor fixes


git-svn-id: svn://svn.berlios.de/openocd/trunk@116 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed breakpoint handling (this changes the target_t interface)


git-svn-id: svn://svn.berlios.de/openocd/trunk@113 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- several small fixes
- retry reading from a FT2232 device on incomplete reads


git-svn-id: svn://svn.berlios.de/openocd/trunk@110 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added support for using Luminary Micro development board 'evb_lm3s811' as a JTAG interface (thanks to Magnus Lundin)


git-svn-id: svn://svn.berlios.de/openocd/trunk@106 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- correctly handle ft2232_device_desc and ft2232_serial when both are given at the same time


git-svn-id: svn://svn.berlios.de/openocd/trunk@104 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- allow FT2232 devices to be opened by serial number instead of device description ('ft2232_serial <serial>' command)
- redirect output from target event scripts (currently only reset) to the daemon output (INFO:)
- some minor fixes and enhancements


git-svn-id: svn://svn.berlios.de/openocd/trunk@103 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added support for AT91SAM7A devices (thanks to Magnus Lundin)
- updated README with pointer to Amontec's JTAGkeyTiny


git-svn-id: svn://svn.berlios.de/openocd/trunk@102 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@101 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- str75x flash support (Thanks to Spencer Oliver)
- correct reporting of T-Bit in CPSR (Thanks to John Hartman for reporting this)
- core-state (ARM/Thumb) can be switched by modifying CPSR
- fixed bug in gdb_server register handling
- register values > 32-bit should now be supported
- several minor fixes and enhancements



git-svn-id: svn://svn.berlios.de/openocd/trunk@100 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- cleaned up str7x flash erase and protect code (use two accesses to erase sectors in both banks)


git-svn-id: svn://svn.berlios.de/openocd/trunk@98 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- set the T bit in the CPSR when the core was executing in Thumb state. Mask the T bit from the CPSR for all CPSR-writing operations


git-svn-id: svn://svn.berlios.de/openocd/trunk@97 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@96 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- integrated patch from Magnus Lundin that fixes at91sam7 flash timing bugs and possible endianness problems (big endian hosts)
- correctly write trailing bytes on str7x flashes
- speed up str7x flash writing by offloading the algorithm to the target


git-svn-id: svn://svn.berlios.de/openocd/trunk@95 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed bug that caused CPSR to be corrupted in Thumb mode


git-svn-id: svn://svn.berlios.de/openocd/trunk@93 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@92 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- bumped OpenOCD version date


git-svn-id: svn://svn.berlios.de/openocd/trunk@91 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- endianess fixes everywhere but in the flash code. flashing might still be broken on big-endian targets and/or hosts
- added access to ARM920T vector catch register (via generic register mechanism)
- don't disable linefills on ARM920T cores - this lead to lockups when accessing lines already contained in cache
- read content of ARM920T cache and tlb into file (arm920t read_flash/read_mmu commands)
- memory reading improved on ARM7/9, can be further accelerated with new "arm7_9 fast_memory_access enable" command (renamed from fast_writes)
- made in_handler independent from in field (makes the handler more flexible)
- added timeout to ft2232 when using D2XX library
- fixed STR7x protection bit handling on second bank (thanks to Bernard)
- added support for using the OpenOCD on AT91RM9200 systems (thanks to Anders Larsen)
- fixed AT91SAM7 flash handling when not running from 32kHz clock (thanks to Anders Larsen)


git-svn-id: svn://svn.berlios.de/openocd/trunk@90 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed bug that could result in register corruption on arm920t targets


git-svn-id: svn://svn.berlios.de/openocd/trunk@89 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@88 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- renamed jtag_interface_t.support_statemove to jtag_interface_t.support_pathmove (it is used to indicate jtag_add_pathmove support)
- fixed small bug in str7x.c that printed an address instead of the target number in an error message
- added support for Olimex ARM-USB-OCD. The new ft2232 layout is called "olimex-jtag"


git-svn-id: svn://svn.berlios.de/openocd/trunk@87 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@86 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- updated configuration examples, installation instructions and README (including list of supported JTAG interfaces)


git-svn-id: svn://svn.berlios.de/openocd/trunk@85 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@84 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added support for FreeBSD ppi (parallel port access similar to /dev/parport on linux) (thanks to Darius for this patch)
- unified 'ftd2xx' and 'ftdi2232' into a single interface 'ft2232'. The library used to access the hardware is choosen during configure with --enable-ft2232_ftd2xx or --enable-ft2232-libftdi.


git-svn-id: svn://svn.berlios.de/openocd/trunk@83 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@82 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed some small memory leaks (thanks to Spencer Oliver)
- verify chip- and buswidth of cfi flash configurations
- added support for ARM966E based systems (tested only with ST micro STR9, thanks to Spencer Oliver)


git-svn-id: svn://svn.berlios.de/openocd/trunk@81 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added GiveIO support to the amt_jtagaccel driver
- explicitly disable loopback mode for FT2232 devices
- changed configuration options n[st]rst_delay to jtag_n[st]rst_delay
- shutdown network services on exit


git-svn-id: svn://svn.berlios.de/openocd/trunk@80 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- added configurable delays after reset lines get deasserted. useful if reset circuitry keeps lines asserted for too long.
- additional debug output when opening the parallel port
- fixed counting of available arm7/9 watchpoint units
- 'flash write' now displays elapsed time


git-svn-id: svn://svn.berlios.de/openocd/trunk@79 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- Added support for native MinGW builds (thanks to Spencer Oliver and Michael Fischer) - you still need to install GiveIO (not part of OpenOCD)
- Added state-move support to ftd2xx and bitbang JTAG drivers (required for XScale, possibly useful for other targets, too)
- various fixes


git-svn-id: svn://svn.berlios.de/openocd/trunk@78 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed handling of services linked list (thanks to Spen for this patch)


git-svn-id: svn://svn.berlios.de/openocd/trunk@76 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- changed fallback implementation of strndup to something that works on all systems (thanks to Spen for this patch)


git-svn-id: svn://svn.berlios.de/openocd/trunk@75 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fixed bug in telnet history handling (patch from John Hartman, thanks)
- OpenOCD version has been changed from SVN revision number to date/time


git-svn-id: svn://svn.berlios.de/openocd/trunk@74 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- fix trunk build for mac os x (patch from Lauri Leukkunen, thanks)
- added check for host endianness, defines WORDS_BIGENDIAN on a big-endian host (e.g. mac os-x)
- fixed bug where endianness of memory accesses could be swapped on BE hosts
- added space for zero termination of ftd2xx_layout string (from Magnus Ludin, tahnks)


git-svn-id: svn://svn.berlios.de/openocd/trunk@73 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@69 b42882b7-edfa-0310-969c-e2dbd0fdcd60

- the 'help' command now takes an optional argument to display help only on a certain command (thanks to Andrew Dyer for this enhancement)
- OpenOCD now includes the ability to diassemble instructions on its own (only ARM for now, Thumb might follow). 
The command is "armv4_5 disassemble <address> <count> ['thumb']" (thumb is currently unsupported).
I've compared the produced disassembly against GDB/GNU Objdump output, and it seems to be correct, but there may still be some bugs left.


git-svn-id: svn://svn.berlios.de/openocd/trunk@68 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@67 b42882b7-edfa-0310-969c-e2dbd0fdcd60

git-svn-id: svn://svn.berlios.de/openocd/trunk@64 b42882b7-edfa-0310-969c-e2dbd0fdcd60