Don't log "Yes, I'm *still* in TAP_IDLE" every seven runtest clocks.

Get rid of needless variable, improve and shrink diagnostic.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

These chips need both SRST and TRST when debugging,
and SRST doesn't gate JTAG.

Now I can issue "reset halt" and have everything act smoothly;
the vector_catch hardware is obviously not kicking in, but the
rest of the reset sequence acts sanely.

 - TAP "setup" event enables the DAP, not omap3_dbginit
   (resolving a chicken/egg bug I noted a while back)
 - Remove stuff from omap3_dbginit which should never be
   used in event handlers
 - Cope better with slow clocking during reset

Also, stop hard-wiring the target name: use the input params in
the standard way, and set up $_TARGETNAME as an output param.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Make the "dap info" output more comprehensible:

 - Don't show CIDs unless they're incorrect (only four bits matter)
 - For CoreSight parts, interpret the part type
 - Interpret the part number
 - Show all five PID bytes together
 - Other minor cleanups

Also some whitespace fixes, and shrink a few overlong source lines.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>

This is the very basic board config for the balloon3 board cpu JTAG
channel.

The rest of the config comprises another 14 .cfg files which I suspect
openocd doesn't really want all of. I'm still not sure how to deal
with this. I'll post another mail/patch to discuss.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Ignore leading '0' characters on hex strings.  For example a bit
pattern consisting of 6 bits could be written as 3f, 03f or 003f and
so on.

Signed-off-by: Michael Roth <mroth@nessie.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

This patch adds basic autoprobing support for the JTAG scan chains
which cooperate.  To use, you can invoke OpenOCD with just:

 - interface spec: "-f interface/...cfg"
 - possibly with "-c 'reset_config ...'" for SRST/TRST
 - possibly with "-c 'jtag_khz ...'" for the JTAG clock

Then set up config files matching the reported TAPs.  It doesn't
declare targets ... just TAPs.  So facilities above the JTAG and
SVF/XSVF levels won't be available without a real config; this is
almost purely a way to generate diagnostics.

Autoprobe was successful with most boards I tested, except ones
incorporating C55x DSPs (which don't cooperate with this scheme
for IR length autodetection).  Here's what one multi-TAP chip
reported, with the "Warn:" prefixes removed:

 clock speed 500 kHz
 There are no enabled taps.  AUTO PROBING MIGHT NOT WORK!!
 AUTO auto0.tap - use "jtag newtap auto0 tap -expected-id 0x2b900f0f ..."
 AUTO auto1.tap - use "jtag newtap auto1 tap -expected-id 0x07926001 ..."
 AUTO auto2.tap - use "jtag newtap auto2 tap -expected-id 0x0b73b02f ..."
 AUTO auto0.tap - use "... -irlen 4"
 AUTO auto1.tap - use "... -irlen 4"
 AUTO auto2.tap - use "... -irlen 6"
 no gdb ports allocated as no target has been specified

The patch tweaks IR setup a bit, so we can represent TAPs with
undeclared IR length.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

And update doc accordingly.  That EmbeddedICE register was
introduced for ARM9TDMI and then carried forward into most
new chips that use EmbeddedICE.

Stop allocating three bytes per IR bit, and cope somewhat better
with IR lengths over 32 bits.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Remove needless debug handler state.

 - "handler_installed" became wrong as soon as the second TRST+SRST
   reset was issued ... so the handler was never reloaded after the
   reset removed it from the mini-icache.

   This fixes the bug where subsequent resets fail on PXA255 (if the
   first one even worked, which is uncommon).  Other XScale chips
   would have problems too; PXA270 seems to have, IXP425 maybe not.

 - "handler_running" was never tested; it's pointless.

Plus a related bugfix: invalidate OpenOCD's ARM register cache on reset.
It was no more valid than the XScale's mini-icache.  (Though ... such
invalidations might be better done in "SRST asserted" callbacks.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Bit 5 shouldn't be used.  Remove all support for modifying it.
Matches the exception vector table, of course ... more than one
bootloader uses that non-vector to help distinguish valid boot
images from random garbage in flash.

Some cosmetic cleanup, and switch to a single table mapping
between state names and symbols (vs two routines which only
share that state with difficulty).

Get rid of TAP_NUM_STATES, and some related knowledge about
how TAP numbers are assigned.  Later on, this will help us
get rid of more such hardwired knowlege.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

 - Use the name mappings all the other code uses:
    + name-to-state ... needed to add one special case
    + state-to-name
 - Improve various diagnostics:
    + don't complain about a "valid" state when the issue
      is actually that it must be "stable"
    + say which command was affected
 - Misc:
    + make more private data and code be static
    + use public DIM() not private dimof()
    + shorten the affected lines

Re the mappings, this means we're more generous in inputs we
accept, since case won't matter.  Also our output diagnostics
will be a smidgeon more informative, saying "RUN/IDLE" not
just "IDLE" (emphasizing that there can be side effects).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

The wrong variable (pc instead of r0) was used.  Furthermore, someone
did cover this error by stupidly silencing the compiler warning that
occurred before a dummy void reference to r0 was added to the code.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

When dumping over 100 registers (as on most ARM9 + ETM cores),
aid readability by splitting them into logical groups.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

The register names are perversely not documented as zero-indexed,
so rename them to match that convention.  Also switch to lowercase
suffixes and infix numbering, matching ETB and EmbeddedICE usage.

Update docs to be a bit more accurate, especially regarding what
the "trigger" event can cause; and to split the issues into a few
more paragraphs, for clarity.

Make "configure" helptext point out that "oocd_trace" is prototype
hardware, not anything "real".

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

retire obsolete mXY_phys commands. Handled by generic memory read/modify commands and target read/write physical memory callbacks.

Added target_read/write_phys_memory() fn's. mdX/mwX commands updated to support phys flag to specify bypassing of MMU.

Merge branch 'master' of ssh://gowinex@openocd.git.sourceforge.net/gitroot/openocd/openocd into HEAD

Retire obsolete and superfluous implementations of virt2phys in each target. This is done in a polymorphic implementation in target.c

Retire obsolete and superfluous implementations of virt2phys in each target. This is done in a polymorphic implementation in target.c

Defined target_write_memory() to be able to handle implementing breakpoints for read only ram(e.g. MMU write protected.